Date   

locked JTAlert 2.16.7 #FT8

k8cr@...
 

JT Alert V 2.16.7 keeps shutting down when I start the program. sometimes after 3-4 times, it will stay active....
Then in about 10 min, it freezes up. Only way to get out of program is to use task manager to end task....

Sometimes get this error message:
Line 35156 (File "C:\Ham_Radio\JTAlertX\JTAlert 2.16.7\JTAlert.exe")"
Error: Variable user without being decleared.....

Any ideas??


locked Re: Computer Crash - Please Remind Me

Michael Black
 

In the Settings here

Inline image

Mike W9MDB




On Monday, June 15, 2020, 11:48:50 AM CDT, Stephen Taylor - K6SJT <stephenk6sjt@...> wrote:


Had a PC crash so setting up JTAlert from beginning. The last item I seem to be missing, I think if my memory serves me, is to have the signal strength displayed along side the call.  Have gone through menus several time and tried the help files but no luck. Any help is appreciated as to where the switch is to turn this signal strength display function on..

Stephen - K6SJT


locked Computer Crash - Please Remind Me

Stephen Taylor - K6SJT
 

Had a PC crash so setting up JTAlert from beginning. The last item I seem to be missing, I think if my memory serves me, is to have the signal strength displayed along side the call.  Have gone through menus several time and tried the help files but no luck. Any help is appreciated as to where the switch is to turn this signal strength display function on..

Stephen - K6SJT


locked Re: Worked Before

Dennis
 

Hi Laurie,
Thanks for your help. I did have the "Ignore B4 status before this date" set to the contest date and the "Do not show Worked Before (B4) Callsigns" clicked - still showed up on the display though. WSJT-X v 2.12, JTAlert v 2.15.3
I would like to just start the log over at zero immediately before the contest and then update the log from the N3FJP software before returning to normal operations. Is this possible?

Kind Regards,
73, Dennis W7DRW


locked Re: v2.16.7 No Sound - Realtec - Windows 10 - WSJT-X v2.2.1

John
 

Tnx Neil,

But the problem is I get no sound when I do that.
I have Win10 Pro
WSJT v2.2.1
JTAlert 2.16.7
Log4OMV1
External sound card

Have logged thousands of contacts and everything works fine except the sound alerts.
They are turned on in the settings section and the Realtek Speaker is set as "Sound Output Device"
However, some times when I open?? a session it will work, but only about 5-10% of the time
73, John

.

On 6/15/2020 6:24 AM, neil_zampella wrote:

As Laurie said previously:

??

To make your life easier, you can perform Sound Output device changes and play tests from the main JTAlert window without having to open the Settings window. Via the "Sound" menu.

??

Just click on Test Sound Output

??

Neil, KN3ILZ

??


-- 
John Mc Hugh, K4AG
Coordinator for Amateur Radio  
National Hurricane Center, WX4NHC
Home page:- http://www.wx4nhc.org

Virus-free. www.avg.com


locked Re: v2.16.7 No Sound - Realtec - Windows 10 - WSJT-X v2.2.1

neil_zampella
 

As Laurie said previously:

 

To make your life easier, you can perform Sound Output device changes and play tests from the main JTAlert window without having to open the Settings window. Via the "Sound" menu.

 

Just click on Test Sound Output

 

Neil, KN3ILZ

 


locked Re: Dual Jtalert and wsjt-x

Jerry <hjerald1@...>
 

Thanks for the info Laurie.

I finally got things to work. I opened each instance separately and made the identical changes to both. At least I guess that is what fixed things? I fiddled with so many other things that in the end I got lost. Nevertheless the end result was positive.

Now if it were possible to get one instance to use a male voice and the other a female voice like is possible with two computers……. That makes is easy to tell from the voice alert which of the two bands has the activity. Perhaps that capability will be in V3?

Jerry KE7DJD

 

From: Laurie, VK3AMA
Sent: Sunday, June 14, 2020 7:12 PM
To: Support@hamapps.groups.io
Subject: Re: [HamApps] Dual Jtalert and wsjt-x

 

 

 

On 15/06/2020 3:49 am, hjerald1@... wrote:

> I set up dual Jtalert and wsjt-x FT8 for 6 and 10 meters on the same

> computer. All is working except the 2nd instance of JTalert (10

> meters) gives no 10 meter audio alerts. If I test the sound card it

> gives the 6 meter voice.  Settings in the 2nd instance of Jtalert is

> grayed out so I can't check settings for a solution.

> What is amiss?

> Jerry KE7DJD

 

There are multiple instance limitations, especially involving access to

the Settings window, documented in the Help File, see the "Multiple

Instances" topic.

 

If you change settings in instance #1, instance #2 will not see those

changes due to each instance using a copy of the config file. It is not

possible within JTAlertV2 for multiple instances to have real-time

access to a single config file and automatically detect and apply

changes. That comes with JTAlertV3.

 

If you change the sound device in instance #1, instance #2 will be

unaware of that change, you will need to make the same change via the

Sound menus which avoids the need to open the Settings window (which is

not possible from instance #2).

 

I just now tested 4 JTAlert instances and each correctly played the Test

Sound.

 

de Laurie VK3AMA

 

 

 

 


locked Re: v2.16.7 No Sound - Realtec - Windows 10 - WSJT-X v2.2.1

John
 



From my original post..

The only way to get JTAlertV2.manager to show as a volume slider in Mixer is to have JTAlert play a sound.

So how do you get it to do that?

73,
John

Virus-free. www.avg.com


locked Re: Dual Jtalert and wsjt-x

Laurie, VK3AMA
 

On 15/06/2020 3:49 am, hjerald1@... wrote:
I set up dual Jtalert and wsjt-x FT8 for 6 and 10 meters on the same computer. All is working except the 2nd instance of JTalert (10 meters) gives no 10 meter audio alerts. If I test the sound card it gives the 6 meter voice.  Settings in the 2nd instance of Jtalert is grayed out so I can't check settings for a solution.
What is amiss?
Jerry KE7DJD
There are multiple instance limitations, especially involving access to the Settings window, documented in the Help File, see the "Multiple Instances" topic.

If you change settings in instance #1, instance #2 will not see those changes due to each instance using a copy of the config file. It is not possible within JTAlertV2 for multiple instances to have real-time access to a single config file and automatically detect and apply changes. That comes with JTAlertV3.

If you change the sound device in instance #1, instance #2 will be unaware of that change, you will need to make the same change via the Sound menus which avoids the need to open the Settings window (which is not possible from instance #2).

I just now tested 4 JTAlert instances and each correctly played the Test Sound.

de Laurie VK3AMA


locked Re: v2.16.7 No Sound - Realtec - Windows 10 - WSJT-X v2.2.1

HamApps Support (VK3AMA)
 

On 15/06/2020 6:35 am, John wrote:
How do I get JTAlertV2.manager to open in the windows Volume Mixer?
Sometimes when I start a session it does and sometimes it doesn't
I tried to execute it in Hamapps/JTAlert/plugins but it still doesn't (when I do this� I get what looks like a DOS screen that flashes too quickly to read).
When it doesn't I get no sound alerts, nor the sound card test voice

Thanks,
John

From my original post..
  • Application volume sliders appearing in the Sound Mixer are controlled by Windows, JTAlert has no control over that.

  • Application volume sliders in the Mixer will only become visible once Windows has detected a sound-play type event from the application.

The only way to get JTAlertV2.manager to show as a volume slider in Mixer is to have JTAlert play a sound. If Windows does not detect that Sound Play event because something is blocking it or it is not running then the Manager will not show in Mixer.

The JTAlertV2.manager executable is a console application without a Windows form and is not designed to be run manually. It is coded to expect a specific number of command-line parameters from JTAlert and to run as a background process without an output window.

de Laurie VK3AMA


locked Re: JTalert

HamApps Support (VK3AMA)
 

On 14/06/2020 11:50 pm, tom harmon wrote:
I have alarms set-up in JTalert . When a alert is triggered in the  window and I click on it nothing happens? Any ideas? I have WSJT-X running also. 73's KD9DVP

What do you expect to happen?

A single left click on a Callsign will send that decode data of that Callsign back to WSJT-X for it to populate the DXCall field and other setup in preparation for a QSO. Please note that WSJT-X will not automatically initiate a QSO if the decode was not a CQ.

de Laurie VK3AMA


locked Re: Decodes window not always populating

HamApps Support (VK3AMA)
 

On 15/06/2020 6:40 am, W4WT wrote:
Not sure what is going on now; the decodes window has been coming up properly every time I've tried it (probably 8 times now).  If and when it fails, I'll do the test you asked for.  Still using 2.16.7 with JTDX 2.1.0-rc149.

Joe W4WT

Tnx Joe.

I'm not sure what was happening, I have some thoughts, but nothing I try can replicate the defect.

de Laurie VK3AMA


locked Re: Worked Before

HamApps Support (VK3AMA)
 

On 15/06/2020 7:26 am, Dennis wrote:
After just participating in the ARRL VHF contest it became apparent that I need to prevent worked before contacts from showing up on the display (I set it so only cq's display). I intend to work field day and expect to have many more contacts than I had during the VHF contest. Is there a simple way to id worked before contacts? I tried changing the parameters within JTAlert, but I didn't get anywhere. Is it possible to reset the "log" to zero to allow it to populate with only contest quo's or is there another way to prevent worked before's showing up on the display?

Kind Regards,
73, Dennis W7DRW

If you don't want to see B4 stations in JTAlert, simple, enable the "Do not show Worked Before..." Alerts Filter.

   

It you want all past worked stations to not show as B4's (until you have worked them) during the contest you can either start with an empty log or use your existing log and set the Worked B4 "Ignore B4 status before this date" option and set the date to the start date of the Contest.

   


de Laurie VK3AMA


locked Re: Dual Jtalert and wsjt-x

hjerald1@...
 

Yes I do that and the test voice works on 10m. However there is never any voice alert when wanted calls appear on jtalert for 10 meters. The 6m voice works all the time.

 

From: Tom Melvin
Sent: Sunday, June 14, 2020 1:28 PM
To: Support@hamapps.groups.io
Subject: Re: [HamApps] Dual Jtalert and wsjt-x

 

Jerry

 

You don’t need to go into setting - use ToolBar - Sound -> Test Sound Output

 

I run two copies 6m and 4m all the time and it works really well.

 

--
73

Tom
GM8MJV (IO85)





On 14 Jun 2020, at 18:49, hjerald1@... wrote:

 

I set up dual Jtalert and wsjt-x FT8 for 6 and 10 meters on the same computer. All is working except the 2nd instance of JTalert (10 meters) gives no 10 meter audio alerts. If I test the sound card it gives the 6 meter voice.  Settings in the 2nd instance of Jtalert is grayed out so I can't check settings for a solution.
What is amiss?
Jerry KE7DJD

 

 


locked Worked Before

Dennis
 

After just participating in the ARRL VHF contest it became apparent that I need to prevent worked before contacts from showing up on the display (I set it so only cq's display). I intend to work field day and expect to have many more contacts than I had during the VHF contest. Is there a simple way to id worked before contacts? I tried changing the parameters within JTAlert, but I didn't get anywhere. Is it possible to reset the "log" to zero to allow it to populate with only contest quo's or is there another way to prevent worked before's showing up on the display?

Kind Regards,
73, Dennis W7DRW


locked Re: Decodes window not always populating

W4WT
 

Hi Laruie,

Not sure what is going on now; the decodes window has been coming up properly every time I've tried it (probably 8 times now).  If and when it fails, I'll do the test you asked for.  Still using 2.16.7 with JTDX 2.1.0-rc149.

Joe W4WT


locked Re: v2.16.7 No Sound - Realtec - Windows 10 - WSJT-X v2.2.1

John
 

Laurie,

How do I get JTAlertV2.manager to open in the windows Volume Mixer?
Sometimes when I start a session it does and sometimes it doesn't
I tried to execute it in Hamapps/JTAlert/plugins but it still doesn't (when I do this� I get what looks like a DOS screen that flashes too quickly to read).
When it doesn't I get no sound alerts, nor the sound card test voice

Thanks,
John

In bullet point form because it is easier to read/follow...
  • There were no changes to audio management in the recent release. There haven't been any changes for several releases.

  • Application volume sliders appearing in the Sound Mixer are controlled by Windows, JTAlert has no control over that.

  • The main JTAlert.exe executable doesn't perform any audio playback and will not appear in the Mixer.

  • All JTAlert audio is managed by the "JTAlertV2.Manager.exe" process and it is this process that will appear in the Mixer.

  • Application volume sliders in the Mixer will only become visible once Windows has detected a sound-play type event from the application.

  • An example from my Realtek (digital) output tests ...

    • Mixer before first sound is played from JTAlert.



    • Mixer after Windows has detected the JTAlert sound-play event.


  • To make your life easier, you can perform Sound Output device changes and play tests from the main JTAlert window without having to open the Settings window. Via the "Sound" menu.

  • I suggest you try tests against other Sound devices regardless of whether they will produce sound. Just a test to see if those devices will show "JTAlertV2.Manager" in the mixer after a test sound is played.

  • If "JTAlertV2.Manager" repeatedly doesn't show in the Mixer for other audio devices then the likely causes are your PC protection software interfering and blocking the UDP control message sent from JTAlert to the Manager process, the "JTAlertV2.Manager" itself is not running or the Audio module of the Manager is not initialized. You can check the status of all Manager modules via the JTAlert "Help -> About" menu.

If you still can't resolve use the "Help" (or "? ") -> "Contact Support" menu, on the main JTAlert window, to send me your JTAlert files for analysis.


de Laurie VK3AMA


-- 
John Mc Hugh, K4AG
Coordinator for Amateur Radio  
National Hurricane Center, WX4NHC
Home page:- http://www.wx4nhc.org

Virus-free. www.avg.com


locked Re: Dual Jtalert and wsjt-x

Tom Melvin
 

Jerry

You don’t need to go into setting - use ToolBar - Sound -> Test Sound Output

I run two copies 6m and 4m all the time and it works really well.

--
73

Tom
GM8MJV (IO85)





On 14 Jun 2020, at 18:49, hjerald1@... wrote:

I set up dual Jtalert and wsjt-x FT8 for 6 and 10 meters on the same computer. All is working except the 2nd instance of JTalert (10 meters) gives no 10 meter audio alerts. If I test the sound card it gives the 6 meter voice.  Settings in the 2nd instance of Jtalert is grayed out so I can't check settings for a solution.
What is amiss?
Jerry KE7DJD


locked Dual Jtalert and wsjt-x

hjerald1@...
 

I set up dual Jtalert and wsjt-x FT8 for 6 and 10 meters on the same computer. All is working except the 2nd instance of JTalert (10 meters) gives no 10 meter audio alerts. If I test the sound card it gives the 6 meter voice.  Settings in the 2nd instance of Jtalert is grayed out so I can't check settings for a solution.
What is amiss?
Jerry KE7DJD


locked Re: Wider window would be nice

André C
 

Hello Laurie,  just to follow up, when do you think you will put version 3 online ?  


Le sam. 13 juin 2020, à 17 h 57, HamApps Support (VK3AMA) <vk3ama.ham.apps@...> a écrit :
On 8/06/2020 11:45 pm, Mark via groups.io wrote:
JTAlert is Great, but I would like to have more information available horizontally.  I have JTAlert's display placed above the WSJT-X display and have room to expand JTAlert's information by four more display fields on each of the three existing rows.

Merk, K6FG

Sorry, that wont happen until JTAlertV3. With JTAlertV2 (the current series) all control placement in the main window is hard-code, it is a major undertaking to increase width and height in order to gain additional callsign display slots.

With the future JTAlertV3 there are no hard-code control placements in any of the windows. Every window can be resized at will and the layout with adjust accordingly. With the Callsigns display specifically, additional callsign display slots are automatically added as the window is resized horizontally, vertically, made full-screen, it doesn't matter.

de Laurie VK3AMA