Date   

locked auto fill logbook

Tom Hone AA0GP
 

Running latest versions of HRD, WSJT-X and jyalert. I have QRZ logging turned on in jtalert under web services but it does not auto fill when contact logged. I have to do a manual lookup. Is there someway to auto fill a QRZ lookup when logging


locked Re: JT Alert 2.50.1 not picking up DXK log file location

Dave Garber
 

I had to set my log4om manually. It would not autofind but i assume cause my lig is on onedrive


On Mon., Jun. 7, 2021, 12:26 p.m. scot, <n2sab@...> wrote:
Hello,

I am running 2.50.1 and have noticed that i am getting an error box that JTA can not confirm that the call was logged, I looked in settings and notice that there is no log file listed on the settings, logging, DXKeeper page. DXKeeper is using the correct log file.

Any Ideas?

Scott
N2SAB


locked Re: JTAlert does nothing.

Don Farrar
 

After turning ACLog off it does start to show call signs, but clicking on them does nothing.
Sometimes the call signs are flashing?
Sometimes no calls show at all?

Don VA3ZV

On Mon, Jun 7, 2021 at 12:53 PM Michael Black via groups.io <mdblack98=yahoo.com@groups.io> wrote:
Does JTAlert work if you don't start ACLog?

Mike W9MDB




On Monday, June 7, 2021, 11:49:10 AM CDT, Don Farrar <va3zedvee@...> wrote:


After upgrading both JTAlert and WSJT-X, JTAlert stopped working?
Went back to Ver 2.16.17 and still nothing?
WSJT-X seems to work and still communicates with ACLog?

Unable to communicate with the WSJT-X process.
  UDP Port : 2237
  IP Address : 127.0.0.1
  Values read from WSJT-X config file...
    C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini

WSJT-X Detected Instance...
  Process Window Title : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
  Process Command Line :

Decode alerts and logging will be unavailable until corrected.

What am I missing?

TAlert Instance      : #1
JTAlert Start Params  : /wsjtx
WSJT-X Window Title   : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
WSJT-X Command Line   :
WSJT-X   --rig-name   :
WSJT-X Config File    : C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini
WSJT-X Version               :
WSJT-X Revision              :
WSJT-X Spec Op Mode          : None
WSJT-X UDP ID                :
WSJT-X UDP Port              : 2237
WSJT-X UDP Server            : 127.0.0.1
WSJT-X UDP MCast on Loopback : False
WSJT-X UDP Max Schema        : 

Don, VA3ZV


locked Re: JTAlert, WSJT with N3FJP for Field Day, all working with exception of mode does not change in N3FJP

David - AK2L
 

Gary,

I am curious.  Why did you bother with N3FJP?  WSJT-X will give you a Cabrillo log and JTAlert will tell you when you have already worked a station on a particular band.

AK2L


locked Re: JTAlert does nothing.

Michael Black
 

Does JTAlert work if you don't start ACLog?

Mike W9MDB




On Monday, June 7, 2021, 11:49:10 AM CDT, Don Farrar <va3zedvee@...> wrote:


After upgrading both JTAlert and WSJT-X, JTAlert stopped working?
Went back to Ver 2.16.17 and still nothing?
WSJT-X seems to work and still communicates with ACLog?

Unable to communicate with the WSJT-X process.
  UDP Port : 2237
  IP Address : 127.0.0.1
  Values read from WSJT-X config file...
    C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini

WSJT-X Detected Instance...
  Process Window Title : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
  Process Command Line :

Decode alerts and logging will be unavailable until corrected.

What am I missing?

TAlert Instance      : #1
JTAlert Start Params  : /wsjtx
WSJT-X Window Title   : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
WSJT-X Command Line   :
WSJT-X   --rig-name   :
WSJT-X Config File    : C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini
WSJT-X Version               :
WSJT-X Revision              :
WSJT-X Spec Op Mode          : None
WSJT-X UDP ID                :
WSJT-X UDP Port              : 2237
WSJT-X UDP Server            : 127.0.0.1
WSJT-X UDP MCast on Loopback : False
WSJT-X UDP Max Schema        : 

Don, VA3ZV


locked JTAlert does nothing.

Don Farrar
 

After upgrading both JTAlert and WSJT-X, JTAlert stopped working?
Went back to Ver 2.16.17 and still nothing?
WSJT-X seems to work and still communicates with ACLog?

Unable to communicate with the WSJT-X process.
  UDP Port : 2237
  IP Address : 127.0.0.1
  Values read from WSJT-X config file...
    C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini

WSJT-X Detected Instance...
  Process Window Title : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
  Process Command Line :

Decode alerts and logging will be unavailable until corrected.

What am I missing?

TAlert Instance      : #1
JTAlert Start Params  : /wsjtx
WSJT-X Window Title   : WSJT-X   v2.4.0   by K1JT, G4WJS, K9AN, and IV3NWV
WSJT-X Command Line   :
WSJT-X   --rig-name   :
WSJT-X Config File    : C:\Users\VA3ZV Mark II\AppData\Local\WSJT-X\WSJT-X.ini
WSJT-X Version               :
WSJT-X Revision              :
WSJT-X Spec Op Mode          : None
WSJT-X UDP ID                :
WSJT-X UDP Port              : 2237
WSJT-X UDP Server            : 127.0.0.1
WSJT-X UDP MCast on Loopback : False
WSJT-X UDP Max Schema        : 

Don, VA3ZV


locked JT Alert 2.50.1 not picking up DXK log file location

scot
 

Hello,

I am running 2.50.1 and have noticed that i am getting an error box that JTA can not confirm that the call was logged, I looked in settings and notice that there is no log file listed on the settings, logging, DXKeeper page. DXKeeper is using the correct log file.

Any Ideas?

Scott
N2SAB


locked Re: JTALERT not docking above WSJT-X #FT8

 

Please disregard . It would help if I had hit the save button. My error. Sorry to bother everyone.
--
73 NU4N Dave


locked Re: JTAlert Alert Window Overflow

Craig
 

GM.  I am using 2.50.1


locked Re: JTAlert Alert Window Overflow

Michael Black
 

What version of JTAlert?

Mike W9MDB




On Monday, June 7, 2021, 07:44:59 AM CDT, Craig <nz4cwcraig@...> wrote:


GM.  In peak hours with a lot of decodes coming from WSJT-X, the JTAlert window as I have configured (3X7) will overflow.  Normally this is not an issue.  Excess alerts will fill the screen and then accumulate without clearing -  multiple decode cycles become necessary for the window to eventually clear and return back to normal.  Is there a selection option which causes alerts that exceed the defined window (3X7) capacity to clear each cycle?

I know from prior posts that the typical response for this is to eliminate alerts filters (like B4's).  Looking to see if fother options that may be there.  Thank you.


locked JTAlert Alert Window Overflow

Craig
 

GM.  In peak hours with a lot of decodes coming from WSJT-X, the JTAlert window as I have configured (3X7) will overflow.  Normally this is not an issue.  Excess alerts will fill the screen and then accumulate without clearing -  multiple decode cycles become necessary for the window to eventually clear and return back to normal.  Is there a selection option which causes alerts that exceed the defined window (3X7) capacity to clear each cycle?

I know from prior posts that the typical response for this is to eliminate alerts filters (like B4's).  Looking to see if fother options that may be there.  Thank you.


locked JTALERT not docking above WSJT-X #FT8

 

I have the parameters for docking above WSJT-X set correctly. Alert is not following WXJT-X
Any ideas ??
Thanks
--
73 NU4N Dave-T


locked jtalert 2.50.1 -decodes window blank

frank
 
Edited

Hello,
2.50.1 vers. work fine,but i have a decodes windows blank,any infos is inside. I work with NET 5,win 10 ,64 bit  .I have this problem with Wsjt-x  and JTDX , FT8 or FT4 .
Thank you
73's de IK5SRE Frank


locked Re: JTAlert, WSJT with N3FJP for Field Day, all working with exception of mode does not change in N3FJP

Dave Garber
 

When i log via jtalert/wsjt the mode is always entered correctly.   Drop down should be able change mode if manually logging.  


On Sun., Jun. 6, 2021, 3:07 p.m. KT7AZ, <kt7az.v69@...> wrote:
Just got all working with JTAlert, WSJT and N3FJP for Field day.  All appears to be functioning except that N3FJP always shows CW Mode (or wherever you set it manually).  Wondering if I am missing something or setting N3FJP mode manually is the only way to change Mode going to log.  

I have the setup where WSJT is connected for radio control and JTAlert does the pass along for logging to N3FJP.

Not a big deal but you know how it gets during a contest.

Thanks,
Gary
--
KT7AZ


locked JTAlert, WSJT with N3FJP for Field Day, all working with exception of mode does not change in N3FJP

KT7AZ
 

Just got all working with JTAlert, WSJT and N3FJP for Field day.  All appears to be functioning except that N3FJP always shows CW Mode (or wherever you set it manually).  Wondering if I am missing something or setting N3FJP mode manually is the only way to change Mode going to log.  

I have the setup where WSJT is connected for radio control and JTAlert does the pass along for logging to N3FJP.

Not a big deal but you know how it gets during a contest.

Thanks,
Gary
--
KT7AZ


locked Re: JTAlert Problem

chas cartmel
 

Do any hotkeys work (see manual)?

73 Charlie

G4EST

www.g4est.me.uk

Stay safe out there

 

 

 

From: Support@HamApps.groups.io [mailto:Support@HamApps.groups.io] On Behalf Of Ernex de la Ossa
Sent: 06 June 2021 09:48
To: Support@HamApps.groups.io
Subject: [HamApps] JTAlert Problem

 

Good morning, I have a problem with JTAlert, after changing from Win 7 to Win10, after installing JTAlert 2.16.17, when running the program, it only shows me the "Decodes" screen but the main screen, where the program settings are , I don't feel like it, so I can't configure the program. I have tried different versions of JTAlert and the same thing always happens. Any subjection?


This email has been scanned by BullGuard antivirus protection.
For more info visit www.bullguard.com


locked JTAlert Problem

Ernex de la Ossa
 

Good morning, I have a problem with JTAlert, after changing from Win 7 to Win10, after installing JTAlert 2.16.17, when running the program, it only shows me the "Decodes" screen but the main screen, where the program settings are , I don't feel like it, so I can't configure the program. I have tried different versions of JTAlert and the same thing always happens. Any subjection?


locked Re: JTAlert 2.50.1 No Alert Colors

Laurie, VK3AMA
 



On 6/06/2021 12:48 pm, Dan Bathker wrote:
"Check the main JTAlert window Settings, "Applications -> WSJT-X/JTDX" section, are the coloring options enabled?"

Answer: YES, the coloring options are enabled; see the attached screen-capture image. Two of the Three coloring options are enabled.

I remain at a loss.

The only reason left for non coloring of the WSJT-X decodes with JTAlert alert colors is not having the Alerts enabled in JTAlert (see under the "Alerts" menu of the main JTAlert window.

If Alerts not enabled is not the problem, then I will need to examine your JTAlert files. Use the "Help" -> "Contact Support" menu, on the main JTAlert window, to send me your JTAlert files for analysis.

Since you're using ADIF logging, followup the support request with a zipped copy of your adif log file. Send it to me direct via
     VK3AMA.Ham.Apps [at] gmail [dot] com

de Laurie VK3AMA


locked Re: JTAlert 2.50.1 No Alert Colors

Dan Bathker
 


Laurie VK3AMA wrote:
"Check the main JTAlert window Settings, "Applications -> WSJT-X/JTDX" section, are the coloring options enabled?"

Answer: YES, the coloring options are enabled; see the attached screen-capture image. Two of the Three coloring options are enabled.

I remain at a loss.

Software is clearly my undoing. (see the 2nd attachment = undoing definition)

If the second attachment fails to attach, the text follows:
"One's undoing is one's downfall; to say, 'It was your own undoing,' means that you were the cause of your own downfall.
You brought this on yourself. You have no one to blame but yourself."

So, I brought this problem on myself.

73
Dan K6BLG
licensed with same US-issued callsign since 1953.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------


On 6/5/2021 3:41 PM, HamApps Support (VK3AMA) wrote:
On 6/06/2021 8:24 am, Dan Bathker wrote:
Yes the UDP settings here in WSJT-X were NOT turned on; one result of my having re-installed both WSJT-X and JTAlert.

So now the UDP settings are all turned ON: See attached image from WSJT-X/Settings/Reporting.

However, no change, I remain with no visual alert colors from JTAlert, I have complete
loss of decode coloring as selected and enabled in JTAlert.

Might there be another common problem resulting in complete loss of decode coloring?

Should I do a *complete* uninstall of JTAlert including deleting the JTAlert Config files in APPDATA as implied by Manuel CT1BXX?
(which is to say, get a complete Fresh Start)

73
Dan K6BLG

While a normal JTAlert reinstall should not affect its existing settings, they may have been lost if your reinstall procedure involves removal of files from the %localappdata% directories.

Check the main JTAlert window Settings, "Applications -> WSJT-X/JTDX" section, are the coloring options enabled?

   

de Laurie VK3AMA


--
Dan Bathker
PO Box 23
La Canada CA 91012

d.bathker@...

Virus-free. www.avast.com


locked Re: JTAlert 2.50.1 Stopped

Dave Garber
 

Using 127.0.0.1  Or multicast 239.255.0.1

And make sure all three check boxes are done in reporting tab of wsjt.    Maybe include a snap shot of settings so mike or Laurie can help

On Sat., Jun. 5, 2021, 7:41 p.m. Jon Baker, <n1zx@...> wrote:
has anyone had a scenario where JTAlert 2.50.1  working 
one day and stopped the next  for no apparent reason ?
The error message seems to indicate a problem with  UDP
ran the UDP setup in help but still not seeing any data from
WSJT-X
can someone point me in the right direction for this

 

5201 - 5220 of 40358