Date   

locked Alerts window does'nt start.

jeff29754 M1BCM
 

Hi guys, could'nt find a fix for this ...
Before installing the new JTAlert version, I first installed the new .net software. Both went with no problems but the Alerts window is a no-show and the QSO history window won't populate. I'm sure it's fixable in settings but I sure as hell can't find it hihi. Report sent.

Jeff M1BCM


locked Re: JTAlert 2.50.1 does not receive from WSJT-X - Callsigns, Activity and Band heat windows don't open

Jim Denneny
 

Known issue. I updated NET to later version.  It works

Jim K7EG


locked Re: JTAlert freezes during start

Jim Denneny
 

Laurie: Definitely not protection software.  Notice from NET here this AM that NET 5.0 has problem.  Recommends upgrade to 5.0.6.  That seems to be my fix..  It has been two days now.

73, Jim K7EG


locked Re: Always on top

Paul F6EXV
 

That was it, Michael, thanks !
73
Paul

Le 24/05/2021 à 11:48, Michael a écrit :

Hi Paul

You'll find it as shown on the picture.

73 de Michael 5p1kzx


JTA on Top
Den 24-05-2021 kl. 10:55 skrev Paul F6EXV:
Hi all
The answer is probably obvious, but I just could not find it...
The JTAlert windows is hidden when I bring another screen on top of it.
But the callsign windows is always on top. Can I change this ? Where please ?
73
Paul F6EXV



Garanti sans virus. www.avast.com


locked Re: Always on top

Michael
 

Hi Paul

You'll find it as shown on the picture.

73 de Michael 5p1kzx


JTA on Top
Den 24-05-2021 kl. 10:55 skrev Paul F6EXV:

Hi all
The answer is probably obvious, but I just could not find it...
The JTAlert windows is hidden when I bring another screen on top of it.
But the callsign windows is always on top. Can I change this ? Where please ?
73
Paul F6EXV


locked Always on top

Paul F6EXV
 

Hi all
The answer is probably obvious, but I just could not find it...
The JTAlert windows is hidden when I bring another screen on top of it.
But the callsign windows is always on top. Can I change this ? Where please ?
73
Paul F6EXV

--
L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast.
https://www.avast.com/antivirus


locked Re: JTAlert 2.50.1 does not receive from WSJT-X - Callsigns, Activity and Band heat windows don't open

Frode Igland
 

My apologies for a late reply and thanks for pointing me to the incorrect UDP setting. I have no recollection of checking it, nor changing the port number, but obviously I must have done so. The good thing is that it works just fine now. Thanks again.

73, Frode LA6VQ 


locked Re: UDP Error

KE7AZ
 

I only have two applications using the UDP port - WSJT-X and JTAlert.  I also tried the multicast set up and it didn't work. 

So I went back to find previous versions to see if I could get something to work.  Here is what I found...
WSJT-X Version     JTAlert version    Result
2.1.2                            2.12.9               OK
2.3.1                            2.15.0               OK
2.3.1                            2.16.17            UDP Error
2.3.1                            2.16.1              AutoIT Crash
2.3.1                            2.16.3              OK
2.3.1                            2.16.6              OK but crashes after settings change
2.3.1                            2.16.11             UDP Error

There was a Windows 10 update just before this appeared.  I tried backing out the update out but one of the updates did not give me the option to undo it.  I did not have a system restore that I could use because of subsequent Windows 10  updates.I suspect that this problem is an unintended consequence of a Windows 10 update.  Entropy is winning!

73
Logan


locked Re: help window problem

Javi LU5FF
 

Laurie thank you very much
that was my problem
everything is ok
73s

Javi - LU5FF
-----------------------

El domingo, 23 de mayo de 2021 17:14:17 ART, Laurie, VK3AMA <hamapps.support@vkdxer.com> escribió:








On 23/05/2021 11:18 pm, Javi LU5FF via groups.io wrote:


  
  
  
HI all...

how to make my window look maximized?

view photo

tnx 

 

Javi - LU5FF


If you can't drag the edges of the Callsigns window to increase its size, make the window active, then press the F2 key which will open the Options, then untick the "Size locked" checkbox which will allow you to resize the window.

   

de Laurie VK3AMA


locked Re: help window problem

Laurie, VK3AMA
 



On 23/05/2021 11:18 pm, Javi LU5FF via groups.io wrote:
HI all...
how to make my window look maximized?
view photo
tnx 
 
Javi - LU5FF

If you can't drag the edges of the Callsigns window to increase its size, make the window active, then press the F2 key which will open the Options, then untick the "Size locked" checkbox which will allow you to resize the window.

   

de Laurie VK3AMA


locked Re: JTAlert freezes during start

Laurie, VK3AMA
 

On 24/05/2021 4:09 am, Jim Denneny wrote:
Rolled back to 2.16.6 and 2.16.7.  Only the settings window opened. No main window starts. NET is 5.0

Next, upgraded NET to 5.0.6 and reinstalled JTAlert 2.50.1 again. It loads now and runs OK.  I have slim confidence that this will remain OK. All exceptions are in place.

Jim K7EG
JTAlert 2.16.17 & .16 do not use the .NET 5 runtime.

.NET 5.0.0 or 5.0.6 will make no difference, both will work with the JTAlert 2.50.x series.

My only thoughts on your troubles are that your Protection software was interfering, or you had an incompatible .NET installed. Perhaps the x86 runtime was installed while trying to use the x64 build of JTAlert. The two need to match. While the x86 versions will work under Windows x64, It is best to keep all architecture types the same, X64 across the board.

de Laurie VK3AMA


locked Re: help window problem

Dave Garber
 

Did you try dragging the edges with your mouse?
Dave Garber
VE3WEJ / VE3IE


On Sun, May 23, 2021 at 2:40 PM Javi LU5FF via groups.io <lu5ff=yahoo.com.ar@groups.io> wrote:
HI all...
how to make my window look maximized?
view photo
tnx 
 
Javi - LU5FF
  •  


locked help window problem

Javi LU5FF
 

HI all...
how to make my window look maximized?
view photo
tnx 
 
Javi - LU5FF
  •  


locked Re: JTAlert freezes during start

Jim Denneny
 

Rolled back to 2.16.6 and 2.16.7.  Only the settings window opened. No main window starts. NET is 5.0

Next, upgraded NET to 5.0.6 and reinstalled JTAlert 2.50.1 again.  It loads now and runs OK.  I have slim confidence that this will remain OK. All exceptions are in place.

Jim K7EG


locked Re: Rollback JTAlert

Michael Black
 

#1 Shut down JTAlert
#2 Rename C:\Users\[username]\AppData\Local\HamApps to HamAppsOld for example

Then run JTAlert again and see if it works.  Could be a corrupt config file.

Mike W9MDB

On Sunday, May 23, 2021, 11:15:36 AM CDT, Jim Denneny <57jndenneny@comcast.net> wrote:





Rolled back to 2.16.7. The settings window opens ok but main window does not open. Is that because NET is at 5.0? At least that is partial progress - no freeze.

Jim K7EG


locked Re: USB Port Shortage

Mike Anderson
 

you can buy 8i or 10 port powered hubs for about $20 bucks  Walmart, best buy  etc etc.  You will need a powered port though.


locked Rollback JTAlert

Jim Denneny
 

Rolled back to 2.16.7. The settings window opens ok but main window does not open. Is that because NET is at 5.0? At least that is partial progress - no freeze.

Jim K7EG


locked JTAlert freezes during start

Jim Denneny
 

Running latest NET and JTAlert.  JTAlert is still freezing on start.  Win 10 latest update.  Added exclusions for WSJT. & JTAlert.  No quarantined items in Protection software.  WSJT runs OK.  Only JTAlert freezes on start.  Ran "Restoro" to sweep for Windows errors.  I have spent days trying to run this down.

Where do I find the install file prior to latest?

Jim K7EG


locked Re: Decode not clearing

John Holmes W9ILY
 

You found it, Laurie. It was the UDP resend option that I had been fooling around with when trying to get a "new" program to work. It didn't work and has been removed but I never went back to uncheck that box. Thanks for your help, as usual!!
73,
John W9ILY


locked Re: Dual callsign

HamApps Support (VK3AMA)
 

On 23/05/2021 5:51 am, Paul F6EXV wrote:
BUT it does not copy the band. I get an error message afeter a while saying "unable to communicate with the JTDX process - UDP Port 2236 - IP address 127.0.01 - Value read from JTDX config file...
So what is going wrong ?

73
Paul F6EXV

Very likely a setup issue with Log4OM preventing JTAlert receiving UDP data from WSJT-X due to using a unicast UDP setup in WSJT-X and Log4OM taking exclusive control of the UDP port (2237).

Switch WSJT-X to using multicast UDP. This will allow multiple applications to concurrently work with WSJT-X. If you're trying to have Lo4OM work with WSJT-X directly, you will need to switch it to using multicast as well, see the Log4OM manual".

See the JTAlert Help file, "WSJT-X UDP setup" topic on how to setup WSJT-X and JTAlert to use multicast.

de Laurie VK3AMA

2721 - 2740 of 37662